Operando X-Ray Absorption Spectroscopic Study on Influence of Specific Adsorption of Sulfo Group in Perfluorosulfonic Acid Ionomer Towards ORR Activity of Pt/C Catalyst

Monday, 10 October 2022
W. Cao, T. Uchiyama, K. Yamamoto, T. Matsunaga, T. Teranishi, R. Sato (Kyoto University), H. Imai (Nissan ARC Ltd.), Y. Sakurai (Japan Synchrotron Radiation Research Institute), Y. Tsuji (FC-Cubic TRA), and Y. Uchimoto (Kyoto University)
Polymer electrolyte fuel cells (PEFCs) are clean energy devices with polymer electrolytes and are expected to play an important role in the development of a global renewable energy system and a pure hydrogen energy society in the future. PEFCs have already been applied for small-scale energy systems such as fuel cell vehicles (FCVs). Pt-based catalysts are basically used due to the relatively inefficient reaction kinetics and catalyst degradation under strong acidic conditions during the oxygen reduction reaction (ORR). However, there are still many difficulties in realizing acceptable cost-effective FCVs. It is known that the ORR activity of Pt-based catalysts is reduced by specific adsorption of anionic species. Perfluorosulfonic acid ionomers such as Nafion® are commonly included in the catalyst layers of PEFCs to provide protonic pathways for promoting the ORR1. However, direct observation of anion adsorption on practical Pt nanoparticle/C catalysts for perfluorosulfonic acid ionomers using X-ray absorption spectroscopy (XAS) still has less report. In this study, to achieve specific adsorption over a higher potential range that is at least equal to the ORR active potential (around 0.90 V vs. RHE), operando XAS measurements were performed; the electronic status and local structural change of Pt atoms induced by the specific adsorption of anions at any potential were observed2.

Pt/C (29.1 wt.%; TEC10V30E) catalyst supported was purchased from TKK. Nafion® solution was employed to prepare Pt/C catalyst ink with I/C ranging from 0.0 to 1.0. And the amount of Pt/C was adjusted to form a 20 µgcarbon cm-2 catalyst layer after dropping 10 μL on a glassy carbon RDE. The electrochemical cell was constructed using a model electrode fabricated in the working electrode, a Pt mesh for the counter electrode, a reversible hydrogen electrode for the reference electrode, and 0.1 M HClO4 aq for the electrolyte. operando XAS measurement of Pt L-edge was carried out in SPring-8 (Japan).

The specific activity decreased as the I/C ratio increased from 0.0 to 0.20. We utilized many methods to evaluate the adsorption species separately, including the measurements of ECSA and oxygen coverage, CO stripping voltammetry, operando X-ray absorption fine structure, and analysis of 5d orbital vacancy. The ECSA and oxygen coverage did not change with increasing ionomer content, indicating that the Pt/C catalyst activity was affected by other adsorption species. A comparison of the CO displacement charge and 5d orbital vacancies of the Pt/C catalysts with I/C = 0.0 and 1.0 suggests that the ionomer-specific adsorption increases when the I/C ratio of the Pt/C catalyst is 1.0; active sites on the surface of the Pt/C catalyst are occupied, resulting in lower catalyst activity.

Acknowledgment

This work was supported by the project (JPNP20003) and a NEDO FC-Platform project commissioned by the New Energy and Industrial Technology Development Organization (NEDO).

References:

[1] Subbaraman, R.; Strmcnik, D.; Markovic, N. M.; et al. J. Chem. Phys. Phys. Chem. 2010, 11, 13, 2825-2833.

[2] Liu, C.; Uchiyama, T.; Uchimoto, Y.; et al. ACS Appl. Energy Mater. 2021, 4 (2), 1143-1149.